AK5 need Australian coin settings

Questions about our products
Post Reply
264060
Posts: 2
Joined: Wed Apr 02, 2008 1:41 pm

AK5 need Australian coin settings

Post by 264060 »

Can you please tell me the settings for Australian coins for the AK5.
Thanks
Geoff
Administrator
Posts: 386
Joined: Mon Jan 15, 2007 6:38 pm

Re: AK5 need Australian coin settings

Post by Administrator »

AK5 set up procedures
Please make you computer and AK5 is power off before connect or disconnect the AK5’s RS232 Interface to your computer!! For best result please power up for 15 minutes before usage
More Detail sees the Weavefuture Coin Acceptor AK5 Manual on http://www.weavefuture.com/pdf/Weavefut ... rAK5-2.pdf
http://forum.weavefuture.com/viewtopic.php?f=8&t=1539
Image
1. Erase the previous all coin ID values setting
• Turn the Sensitive switch to “NOM” position
• Turn the setting switch to the “SET” position enter programming mode, LED display “00”
• Keep press the Adjust Setting Switch 5 seconds or more until hear a “Beep” sound and LED display “C”, means all the coin value setting is erased
• Turn the setting switch to the “START” position exit programming mode
2. Set coin ID values
• Turn the Sensitive switch to the “NOM” position
• Turn the Setting Switch to the “SET” position enter programming mode, LED display “00”
• Press the Adjust Setting Switch to adjust the coin value in turn and let the LED display the desirable Coin ID value, for example “01” or “02”. The value increase 1 upon 1 press. If the desirable value passed, just turn the setting switch to “START” then turn back to “SET” again the LED will display “00”, the value can be selected again.
• Deposit the coins in turn, can program up to 10 coins .If less than 10 coins can add and store later. For example can prepare 10 quarters as different condition as possible. Or can deposit 10 same or different tokens.
Power adaptor output 12VDC adaptor (around 500mA) • Repeat above two steps to set other coin ID values.
Turn the setting switch to the “START” position to exit programming mode
Example B : Setup for AUD (2.00), AUD (1.00), AUD (0.20), AUD (0.10), AUD (0.05).
1. Clear all the settings. Following above steps 1 and 3 to erase previous settings.
2. Prepare 10 sets of AUD (2.00), AUD (1.00), AUD (0.20), AUD (0.10), AUD (0.050)s.
3. Turn the Sensitive Switch to NOM
4. Turn the Setting Switch to SET going to Programming mode, the display will show “00”
5. press Adjust Setting Switch once, the display will show “01” which stands for Coin ID= 1 in PC, drop the 10 AUD (2.00)s in sequence, when drop the 10th AUD (2.00), the display will show “F” means the setting is done.( if press more time accidentally, for example the display show “01” or “02”, then turn the Setting Switch to START, then turn Setting Switch to SET again the display will show “00”.)
6. press Adjust Setting Switch once, the display will show “02” which stands for Coin ID= 2 in PC, drop the 10 AUD (1.00) in sequence, when drop the 10th AUD (1.00), the display will show “F” means the setting is done
7. press Adjust Setting Switch once, the display will show “03” which stands for Coin ID=3 in PC, drop the 10 AUD (0.20) in sequence, when drop the 10th AUD (0.20), the display will show “F” means the setting is done.
8. Press Adjust Setting Switch 3 times until the display show “04” which stands for Coin ID= 4 in PC, drop the 10 AUD (0.10) in sequence, when drop the 10th AUD (0.10), the display will show “F” means the setting is done.
9. Press Adjust Setting Switch 4 times until the display show “05” which stands for Coin ID= 5 in PC, drop the 10 AUD (0.05) in sequence, when drop the 10th AUD (0.05), the display will show “F” means the setting is done.
10. Turn Setting Switch to START, then your AK5 is ready to use.
11. When drop 1 AUD (2.00), it will send to PC as Coin ID= 1; drop 1 AUD (1.00), it will send to PC as Coin ID= 2; drop 1 AUD (0.20), it will send to PC as Coin ID=3; drop 1 AUD (0.10)it will send to PC as Coin ID= 4; drop 1 AUD (0.05)it will send to PC as Coin ID= 5;
12. Please reference the software Weavefuture Coin Acceptor AK5 Configuration part for detail
1 INSTALLATION SOFTWARE PROCEDURE
1.1 Check you PC’ Com port availability
1.2 Install the software.
1.3 Configure the Weavefuture Coin Acceptor Driver and Usage of PC
1.4 Reboot the PC
Bring up the Weavefuture AK5 Coin Acceptor Configuration Windows to configure the minutes to use relate to Coin ID after finish installation
The Com port is default COM1.
Coin ID is 1,2,3,4,5 have to match with the hardware Coin Acceptor AK5’s configuration, The default value has been set AUD (2.00), AUD (1.00), AUD (0.20), AUD (0.10), AUD (0.05) match the Coin ID configured in AK5 as Coin ID 1, 2, 3, 4,5. If you there is any problem, you can reprogram it following the above example.
Important: Program will start default to run “Weavefuture Kiosk Timer Test”, which will not lock the screen and special keys.
After finish test for coin acceptor successfully, then you can select “RUN Weavefuture Kiosk Timer” and save the change.
Post Reply